Skip to main content
Version: 18

Design

Fire design on elevated temperature

Consteel performs cross section resistance and buckling checks for all steel members which are subjected to fire effect by using the adequate formulas from the EuroCode 3 standard.

Classification of cross-section (EN 1993-1-2 4.2.2)

Cross-sections are classified as for normal tempereature (EN 1993-1-1) but using the reduced value for ε.

ε=0,85[235fy]0,5\varepsilon = 0,85 \left [\dfrac {235} {f_y} \right ] ^{0,5}

Tension (EN 1993-1-2 4.2.3.1)

Permanent temperature ((1))

Nt,fi,Θ,Rd=ky,Θ[γM,0γM,fi]Npl,RdN_{t,fi,\Theta,Rd} = k_{y,\Theta}\cdot \left [\dfrac {\gamma_{M,0}} {\gamma_{M,fi}} \right ]\cdot N_{pl,Rd}\qquad \qquad (Class 1-4)

Where
ky,Θk_{y,\Theta}\qquad\qquad acc. to EN 1993-1-2 Table 3.1
Npl,RdN_{pl,Rd}\qquad\qquad the design resistance for normal temperature

Varying temperature ((2))

Nt,fi,t,Rd=Anon,tfyγM,fiN_{t,fi,t,Rd} = A_{non,t}\cdot \dfrac {f_y} {\gamma_{M,fi}}\qquad \qquad (Class 1-4)

Compression (Class 1-3: EN 1993-1-2 4.2.3.2, Class 4: + Annex E.2)

Permanent temperature ((1))

Nc,fi,t,Rd=Aky,ΘfyγM,fiN_{c,fi,t,Rd} = A\cdot \dfrac {k_{y,\Theta}\cdot f_y} {\gamma_{M,fi}}\qquad \qquad (Class 1-3)

Nc,fi,t,Rd=Aeffkp0,2,ΘfyγM,fiN_{c,fi,t,Rd} = A_{eff}\cdot \dfrac {k_{p0,2,\Theta}\cdot f_y} {\gamma_{M,fi}}\qquad \qquad (Class 4)

Where
kp0,2,Thetak_{p0,2,\\Theta}\qquad \qquad acc. to EN 1993-1-2 Table 3.1

Varying temperature ((6))

Conservative way, case (1) where Θa=Θa,max\Theta_a = \Theta_{a,max}

Bending (EN 1993-1-2 Class 1-2: 4.2.3.3; Class 3: 4.2.3.4; Class 4: + Annex E.2)

Permanent temperature ((1))

Mfi,Θ,Rd=ky,ΘγM,0γM,fiMRdM_{fi,\Theta ,Rd} = k_{y,\Theta}\cdot \dfrac {\gamma_{M,0}} {\gamma_{M,fi}}\cdot M_{Rd}\qquad

Where

MRd=Mpl.RdM_{Rd}=M_{pl.Rd}\qquad or in the case of shear: MRd=MV.RdM_{Rd}=M_{V.Rd}\qquad \qquad (Class 1-2)

MRd=Mel.RdM_{Rd}=M_{el.Rd}\qquad or in the case of shear: MRd=MV.RdM_{Rd}=M_{V.Rd}\qquad \qquad (Class 3)

MRd=Meff.RdM_{Rd}=M_{eff.Rd}\qquad \qquad \qquad \qquad \qquad \qquad \qquad \qquad \qquad \qquad (Class 4)

ky,Θk_{y,\Theta}\qquad \qquad acc. to EN 1993-1-2 Table 3.1

Varying temperature ((2))

Mfi,t,Rd=Wpl,non,tfyγM,fiM_{fi,t,Rd} = W_{pl,non,t}\cdot \dfrac {f_y} {\gamma_{M,fi}}\qquad \qquad (Class 1-2)

Mfi,t,Rd=ky,Θ,maxγM,0γM,fi1κ1κ2M_{fi,t,Rd} = k_{y,\Theta ,max}\cdot \dfrac {\gamma_{M,0}} {\gamma_{M,fi}}\cdot \dfrac {1} {\kappa_1\cdot \kappa_2}\qquad \qquad (Class 3)

Mfi,t,Rd=kp0,2,Θ,maxγM,0γM,fi1κ1κ2Meff,RdM_{fi,t,Rd} = k_{p0,2,\Theta ,max}\cdot \dfrac {\gamma_{M,0}} {\gamma_{M,fi}}\cdot \dfrac {1} {\kappa_1\cdot \kappa_2}\cdot M_{eff,Rd}\qquad \qquad (Class 4)

Shear (EN 1993-1-2 Class 1-2: 4.2.3.3(6); Class 3: 4.2.3.4(4); Class 4: + Annex E.2)

Permanent temperature

Vfi,t,Rd=ky,Θ,webγM,0γM,fiVRdV_{fi,t,Rd} = k_{y,\Theta ,web}\cdot \dfrac {\gamma_{M,0}} {\gamma_{M,fi}}\cdot V_{Rd}\qquad \qquad (Class 1-4)

Varying temperature

ky,Θ,webk_{y,\Theta ,web}\qquad \qquad the hottest point in the web

In case of complex internal forces Consteel use the conservative interaction formula neglecting the effect of shear:

Nfi,EdNfi,Θ,Ed+My,fi,EdMy,fi,Θ,Ed+Mz,fi,EdMz,fi,Θ,Ed1\dfrac {N_{fi,Ed}} {N_{fi,\Theta ,Ed}}+\dfrac {M_{y,fi,Ed}} {M_{y,fi,\Theta ,Ed}}+\dfrac {M_{z,fi,Ed}} {M_{z,fi,\Theta ,Ed}}\leq 1\qquad \qquad

Global stability resistance

To calculate the global stability resistance for fire design situation, Consteel uses EuroCode General method (EN 1993-1-1 6.3.4) as for normal temperature but using the proper buckling curves:

For compression

χfi=1φΘ+φΘ2λˉΘ2\chi _{fi}=\dfrac {1}{\varphi_{\Theta}+\sqrt{\varphi_{\Theta}^2-\bar{\lambda}_{\Theta}^2}}

For bending

χLT,fi=1ϕLT,Θ,com+ϕLT,Θ,com2λˉLT,Θ,com2\chi _{LT,fi}=\dfrac {1}{\phi_{LT,\Theta ,com}+\sqrt{\phi_{LT,\Theta ,com}^2-\bar{\lambda}_{LT,\Theta ,com}^2}}

Critical temperature calculation

The critical temperature calculation can be activated in the design settings window. This option is only active if the following conditions are met

  • at least one member with reactive fire protection
  • at least one fire load case set to room temperature analysis
  • at least one load combination with fire load case is selected for global design

The results of the calculation can be queried in the Design Parameters drop-down menu. The results are displayed in a colored graphic. You can also open the Section Module from here by right-clicking on a given section, where the details of the critical temperature calculation can be found. The first line of the summary reads whether the profile should be protected or not, and the critical temperature field contains the relevant part of EC, the applied fire curve, the unprotected fire resistance time and temperature reached of the profile and the required fire resistance time.